How To Repair Seatback Release On 2008 Nissan Altima

Coupe

Operating tips

Alarm

Earlier driving the vehicle, render the seatback to an upright seating position afterwards manually releasing it. As well, make sure the seat is locked in identify. Failure to do then may cause the seat to move in a collision or sudden stop. This may result in impairment to the seat or personal injury.

CAUTION

● Practise not operate the power recline switch when the seatback has been manually released using the upper seatback release lever 1 . Doing so can damage the seat.
● Practise non pull on the upper seatback release lever or the trim to return the seatback to a normal seating position. Doing and so may harm the seat.

● The power seat motor has an machine-reset overload protection circuit. If the motor stops during functioning, wait 30 seconds, then reactivate the switch.
● Exercise non operate the power seat switch for a long period of time when the engine is off. This will belch the battery.
● Pull upward on the upper seatback release lever to release the seatback only. Push the seatback forrad to allow for access to items behind the front seat. Push the seatback to the rear of the vehicle to return the seatback to the upright and locked position. The upper seatback release lever does not demand to be used.

Sedan

Forward and backward

Moving the switch forward or astern will slide the seat forward or backward to the desired position.

Reclining

Motility the recline switch astern until the desired angle is obtained. To bring the seatback forward over again, move the switch forward and move your body frontward. The seatback will move forward.

The reclining feature allows aligning of the seatback for occupants of different sizes for added condolement and to assistance obtain proper seat belt fit (encounter "Precautions on seat belt usage" later in this department). As well, the seatback can be reclined to permit occupants to residuum when the vehicle is stopped and the transmission is in P (Park) or North (Neutral) position with the parking brake fully practical.

Coupe shown, Sedan like

Seat lifter (if so equipped for driver'due south seat)

Pull the lever upward or push button downwards to accommodate the angle and peak of the seat cushion.

Type A

Blazon B

Lumbar support (if and then equipped for driver'southward seat)

The lumbar support feature provides lower back support to the driver. Push button the switch (Type A) forward or backward or move the lever (Blazon B) upwardly or down to adjust the seat lumbar area.

Entry to the rear seat from outside of the vehicle (if so equipped for Coupe models)

Pull the seat recliner lever to the uppermost position folding the seatback frontward, releasing the seat rails.

Slide the unabridged seat forrad for access to the rear seat.

To return the seat to a locked position: Push button the upper seatback rearward until the seatback and track are locked.

Operating tips:

● The seatback and track will not lock until the seatback is returned rearward.
● The seatback will render to the first locking notch when using the seat recliner lever.

CAUTION

● When returning the seat to its original position, confirm that the seat and seatback are locked properly.
● Exist careful not to pinch your hand or foot or bump your head when operating the walk-in seat.

Exiting from the rear seat on the passenger's side, using the upper seatback release lever (if so equipped for Coupe models)

Pull the upper seatback release lever 1 to the uppermost position, folding the seatback forward 2 , releasing the seat runway.

Slide the unabridged seat forrard to leave from the rear seat.

To render the seat to a locked position:

Push the upper seatback rearward until the seatback and track are locked.

Operating tips:

● The seatback and track volition not lock until the seat back is returned rearward.

● The seatback will return to an upright seating position if the upper seatback release lever is pulled to the uppermost position.

CAUTION

● When returning the seat to its original position, ostend that the seat and seatback are locked properly.

● Be careful not to pinch your mitt or foot or bump your head when operating the walk-in seat.

Front manual seat adjustment

Forward and astern Pull the center of the bar upward and hold it while you slide the seat forward or astern to the desired position. Release the bar to lock the seat in position. Reclining T ...

Encounter also:

Tire And Loading Information Placard Location
NOTE: The proper common cold tire aggrandizement pressure is listed on the driver's side B-Pillar or the rear edge of the driver's side door. Tire Placard Location ...

Outside rear view mirrors
Mirror angle tin exist adjusted using the switch. To select a mirror to arrange, press the switch. i Left 2 Right To adapt the mirror, press the switch. ane Up ii Right iii Downward iv Left Fold ...

Location of the Tire Label (Placard)
You will detect the tire characterization containing tire inflation force per unit area past tire size and other important information on the commuter's side B-pillar or on the edge of the driver's door frame. SAMPL ...

Source: https://www.m-sedan.com/front_power_seat_adjustment-4821.html

Posted by: birchproome.blogspot.com

Share this post